The Pivot Cleaner
Clean tools before your next client sits down.
Your brush can't get inside the hinge. Tiny bubbles can. Drop your tools in, press one button, walk away for four minutes.
- Gets into hinges, grooves and grips
- Just water — nothing to buy again
- 650ml flat tank, so long tools lie down properly
- 3, 6 or 12 minutes. One button.
You scrub it. The dark line stays.
You hold the nippers up to the light. There it is, right in the joint. You scrub again. It's still there.
That's not you rushing. A bristle is too fat to fit in a hinge. It was never going to get in there.
Clean comes first for a reason.
Everything you do after cleaning assumes the tool is already clean.
Your state writes the order down. Texas says metal tools get cleaned, then disinfected, before every single service. Georgia says you can't use a tool on a client unless it's been cleaned properly first.
Anything left behind is sitting between the tool and whatever you put it in next.
Bubbles go where bristles can't.
Fill the tank with water. The machine shakes it so fast that millions of tiny bubbles form — far too small to see.
They pop against every surface the water touches. Inside the hinge. Down in the grooves. All over the grip. Nothing has to fit into the gap, because the water is already in there.
No scrubbing. Nothing scratches.
Most of them weren't built for your tools.
They're round and deep, and a plastic tray takes up half the space. Long thin tools end up propped at an angle instead of lying flat.
Round tanks with trays
- Long tools sit at an angle
- The tray eats the space you paid for
- Deep and narrow — awkward to fill and empty
The Pivot Cleaner
- Flat rectangular tank — pushers and nippers lie down
- 650ml, no tray — you get the whole tank
- 3, 6 or 12 minutes — light dust to heavy buildup
- Water only — nothing to reorder
Four minutes. Three steps.
Fill it
Warm water up to the line. That's all it needs.
Drop tools in
Open them up, don't stack them. Lid on. Pick a timing.
Rinse and dry
Rinse them off, dry them well, carry on as normal.
Any tool with somewhere to hide.
- Nail Nippers, pushers, clippers, e-file bits.
- Skin Extractors, tweezers, lash tools, steel tools.
- Barber Clipper blades, guards, shear pivots.
- Brow & lash Slant and point tweezers, applicators.
- Between clients Short cycle while you reset the station.
- End of day One long cycle for the whole drawer.
What you're getting.
| Tank capacity | 650 ml (22 oz) |
| Frequency | 49 kHz |
| Timings | 3, 6 and 12 minutes |
| Controls | Touch panel |
| Tank | Rectangular stainless, no tray |
| Runs on | Water only |
| Weight | 580 g |
| Plug | US mains |
| In the box | Cleaner, cable, instructions |
Things people ask.
Does this replace disinfecting?
No. It cleans. You still disinfect after, exactly like you do now. Cleaning first just means the disinfecting step isn't working around leftover gunk.
Do I still need to brush my tools?
Yes. Brush them like normal, then run them through this to get what's left in the joints.
Do I need special liquid?
No. Warm water. That's one less thing to keep buying.
How loud is it?
About like an electric toothbrush. You can run it with a client in the chair.
Will it ruin my shears?
No — nothing scrapes or scratches. Dry them well and re-oil the pivot after. If your shears have a tension screw, check what the maker says.
What shouldn't go in?
Nothing with a battery or motor — take the blade off the clipper, don't put the clipper in. No makeup brushes; the water loosens the glue in the metal band. Dry carbon steel straight away or it spots. And never bleach in the tank.
What size tools fit?
The tank holds 650ml and it's flat and rectangular with no tray, so long thin tools lie down instead of propping up at an angle. Email us if you want exact inside measurements for a specific tool.
Does it tick my state board's box?
Rules are different in every state, so check yours. Ultrasonic cleaning shows up in industry guidance as a way to do the cleaning step that comes before disinfecting.
How fast does it ship?
Out the door in 1–3 working days. Most US orders land 7–12 days after that.
I need a few for the salon.
Take the two or three pack above, or email hello@pivotsupply.com if you need more than that.
What if I don't like it?
Send it back within 30 days and we'll refund you. No argument, no form to fill in.
Brush one set like you always do.
Then run it through.
Look at the water afterwards. That's what was still on them.
Free US shipping · 30-day returns · Bulk pricing above